sunbet(中国)

    LRRK2-RCKW: MLi-2: E11 DARPin cryo-EM sample preparation

    Marta Sanz Murillo, Andres Leschziner

    Published: 2023-10-24 DOI: 10.17504/protocols.io.q26g7p17qgwz/v1
    AI 解读
    浏览 1606

    Abstract

    Protocol used to prepare LRRK2-RCKW: DARPin:MLi-2 complex and cryo-EM grid preparation.

    Before start

    Make

    Steps

    Protein purification and buffer exchange

    1.

    His6-Z-TEV-LRRK2-RCKW was expressed and purified as described in a previous protocol.

    LRRK1 expression and purification

    2.

    Prepare LRRK2 buffer exchange. Keep it at 4ºC.

    20 millimolar (mM) HEPES pH=7.4

    150 millimolar (mM) NaCl

    2.5 millimolar (mM) MgCl2

    20 micromolar (µM) GDP

    0.5 millimolar (mM) TCEP

    3.

    Spin down purified LRRK2-RCKW (10000 rcf, 4°C, 10 minutes). Leave protein on ice afterward.

    For the best result, keep protein on ice and reduce the amount of time between spinning

    and freezing cryo-EM samples.

    4.

    Exchange buffer using a spin desalting column (ZebaTM Spin Desalting Columns, 7K MWCO (Catalog number: 89877).

    5.

    Spin down again the exchange buffer LRRK2-RCKW (10000 rcf, 4°C, 10 minutes) and measure the concentration. Leave protein on ice afterward

    Citation
    The initial concentration range was 20-40 uM. The final concentration might be half of the initial one. Final volume might be 13-16 uL.

    5.1.

    Thaw E11 DARPin and spin it down. Measure its concentration.

    6.

    Dilute MLi-2 stock (diluted in 100% DMSO) to a desired concentration

    7.

    Based on LRRK2-RCKW concentration, add the necessary volume to get a proportional ratio

    LRRK2:DARPin:MLi-2 1:1.25:3 and dilute to a final 10 micromolar (µM) LRRK2-RCKW concentration using exchange buffer (150 mM NaCl).

    8.

    Incubate 10 minutes at RT. Afterward, keep it on ice until grid preparation.

    E11 DARPin purification

    9.

    E11 DARPin purified as described in the next protocol

    cryo-EM sample preparation

    10.

    We used UltraAuFoil Holey Gold 2/2 200 mesh grids and plasma cleaning them in the Solarus II (Gatan) using the QuantiFoil Au preset.

    11.

    Dilute the sample to the desired concentration using the LRRK2 exchange buffer. We used 6 micromolar (µM).

    12.

    Apply 3 to 3.5 microliters (µl) of sample and plunge freeze. We used a

    Vitrobot (FEI) to blot away excess sample and plunge freeze in ethane liquid. (In

    our case, we use 4 seconds as a time blot as 20 sec as a wait time and 4 as a blot force, but these

    parameters are slightly different from one Vitrobot to another. I would try

    with the Vitrobot parameters already tested in your machine first).

    13.

    Store grids in liquid nitrogen until ready for imaging

    推荐阅读

    Nature Protocols
    Protocols IO
    Current Protocols
    扫码咨询